Cisco's CPE resources exceeded

[Dan Morphis]

What does the syslog on the cpe contain? That will likely contain info on why the cpe is faulting. Did you change the parameters and restart the cwmp process?

-dan

> On May 31, 2015, at 11:53 PM, Fabien Bazille <fab.baz22 at gmail.com> wrote:
> 
> Thank you Manny,
> 
> Dan, here is the log:
> 00000C-CISCO887%252dK9V01-FCZ154390G7: Inform (1 BOOT); retry 
> count 0
> 
> 00000C-CISCO887%252dK9V01-FCZ154390G7: Started task refreshObject(556c0ec04de397db3655201c)
> 
> 00000C-CISCO887%252dK9V01-FCZ154390G7: Fault response for task 556c0ec04de397db3655201c. Retrying after 300 seconds.
> 
> And the Fault tells me resource exceeded.
> 
> 
> 
> 2015-05-29 18:25 GMT+02:00 Manny Veloso <manny.veloso at smartrg.com>:
>> That error is probably the Cisco CWMP client barfing. Some CWMP clients run out of memory when dumping their whole tr-98/181 tree, especially the older ones.
>> 
>> The good thing is it tells you it’s dead, instead of just, well, dying. The below parameters should help.
>> -- 
>> Manny Veloso
>> Sr. Solutions Engineer
>> Smartrg.com
>> 
>> From: Dan Morphis <dan at milkcarton.com>
>> Reply-To: Community support for GenieACS users <users at lists.genieacs.com>
>> Date: Friday, May 29, 2015 at 8:55 AM
>> To: Community support for GenieACS users <users at lists.genieacs.com>
>> Subject: Re: Cisco's CPE resources exceeded
>> 
>> Fabien,
>>   Without seeing a log, I can only speculate that the connection is timing out.
>> 
>> Try adjusting the GET_PARAMETER_NAMES_DEPTH_THRESHOLD and SESSION_TIMEOUT values. The wiki has
>> information on more information on the values to try. Remember to restart the cwmp worker after adjusting the values.
>> 
>> In my environment, I had to use
>>   "GET_PARAMETER_NAMES_DEPTH_THRESHOLD" : 2,
>>   "SESSION_TIMEOUT" : 90,
>> 
>> -dan
>> 
>>> On Fri, May 29, 2015 at 12:04 AM, Fabien Bazille <fab.baz22 at gmail.com> wrote:
>>> Hi,
>>> 
>>> I'm trying to add some Cisco routers in my network pro supervision and provision.
>>> After i start the cwmp on the cisco, the device is correctly added to GenieACS, but for the task: RefreshObject i get a resources exceeded fault code (9004).
>>> And when i look to a capture the frame causing that problem is the GetParameterValues from the ACS.
>>> 
>>> My training concern the setup of GenieACS, that's why i open so much issues and I'm sorry for that.
>>> 
>>> Thank you for your time.
>>> 
>>> Best regards,
>>> 
>>> Fabien B
>>> 
>>> _______________________________________________
>>> Users mailing list
>>> Users at lists.genieacs.com
>>> http://lists.genieacs.com/mailman/listinfo/users
>> 
>> 
>> _______________________________________________
>> Users mailing list
>> Users at lists.genieacs.com
>> http://lists.genieacs.com/mailman/listinfo/users
> 
> _______________________________________________
> Users mailing list
> Users at lists.genieacs.com
> http://lists.genieacs.com/mailman/listinfo/users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.genieacs.com/pipermail/users/attachments/20150601/bb55b70b/attachment.html>